Tabor Hochspannungs-Signalverstärker

300Vp-p Single-Channel Signal Amplifier
9100 Amplifier

The 9100 is a single-channel, 2U, half-rack size, bench-top power amplifier designed for signal amplification. With unprecedented signal purity, Model 9100 amplifies signals from DC to over 500 KHz. The unit has a fixed gain of x15 however the same amplifier is available with custom gain and no signal purity or performance degradation whatsoever.

  • High voltage output to 300Vp-p (±150V)
  • Output current to 150 mA
  • Wideband range to over 500 kHz
  • Slew rate to 200V/µs
  • Low distortion
  • Custom configuration of gain and signal ground
400Vp-p Single-Channel Signal Amplifier
9100A Amplifier

The 9100A was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It’s a single four channel built in a small case size to save space and cost but without compromising bandwidth and signal integrity.

  • Single channel
  • High voltage output to 400Vp-p (±200V)
  • Output current to 125 mA
  • Slew rate to 400V/µs
  • Monitor output
  • Precise signal amplification for multiple applications
  • Full power bandwidth from DC to >500 kHz
300Vp-p Dual-Channel Signal Amplifier
9200 Amplifier

The 9200 is a dual-channel, 2U, half-rack size, bench-top power amplifier designed for signal amplification. With unprecedented signal purity, Model 9200 amplifies signals from DC to over 500 kHz. The unit has a fixed gain of x15 however the same amplifier is available with custom gain and no signal purity or performance degradation whatsoever.

  • High voltage output to 300Vp-p (±150V)
  • Output current to 100 mA per channel
  • Wideband range to over 500 kHz
  • Slew rate to 200V/µs
  • Low distortion
  • Custom configuration of gain and signal ground
400Vp-p Dual-Channel Signal Amplifier
9200A Amplifier

The 9200A was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It has two channels built in a small case size to save space and cost but without compromising bandwidth and signal integrity.

  • Dual independent channels
  • Monitor Outputs for each channel
  • Precise signal amplification for multiple applications
  • Full power bandwidth from DC to >500 kHz
  • Slew rate to 400V/µs
  • -200 to +200 V (400 Vp-p) with up to 100 mA output current
  • Special unipolar mode for MEMS engine drivers

9250

30MHz Differential / Dual-Channel Signal Amplifier
9250 Amplifier

The 9250 is a bench-top, 2U, half 19” rack size, fully metal case dual channel amplifier. The instrument can be configured to be used as two single-ended independent channels, or as one input with two differential outputs. The waveform-amplifier combo is an ideal solution for virtually any high-voltage, wide bandwidth application.

  • Large signal bandwidth to 15 MHz
  • Small signal bandwidth to 30 MHz
  • High amplitude to 40Vp-p (into high impedance)
  • Slew rate to 500V/µs
  • Low distortion
  • Custom configuration of: gain, input impedance, output impedance, output configuration

9260

45MHz Differential / Dual-Channel Signal Amplifier
9260 Amplifier

The 9260 is a bench-top, 2U, half 19” rack size, fully metal case dual channel DC coupled wideband amplifier designed for high frequency, high current signal amplification. The instrument can be configured to be used as two single-ended independent channels, or as one input with two differential outputs. The 9260 is the ideal complimentary amplifier to any signal source that needs a supporting power boost for demanding applications.

  • 45MHz bandwidth
  • High amplitude to 34Vp-p into 50Ω
  • High output current drive to 1A
  • Fast transition time of <10ns
  • Low distortion
  • Custom configuration of: gain, input impedance, output configuration

9400

400Vp-p Four-Channel Signal Amplifier
9400 Amplifier

The 9400 was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It has four channels built in a small case size to save space and cost but without compromising bandwidth and signal integrity.

  • Four independent channels
  • Monitor outputs for each channel
  • Precise signal amplification for multiple applications
  • Full power bandwidth from DC to >500 kHz
  • Slew rate to 400V/µs
  • -200 to +200 V (400 Vp-p) with up to 50 mA output current
  • Special unipolar mode for MEMS engine drivers

A10150

150MHz 16Vp-p Single Channel Signal Amplifier
A10150 Amplifier

Model A10150 is an ultra-small footprint, wideband, DC coupled amplifier designed for high frequency, low distortion signal amplification. With a high bandwidth of 150MHz, 20Vp-p into 50Ω and a fast transition time of less than 1.8ns, the A10150 is the ideal complimentary amplifier to any high speed signal source that needs a supporting power boost for demanding applications.

  • 150MHz bandwidth
  • High amplitude to 20Vp-p into 50Ω
  • Fast transition time of <1.8ns
  • Small footprint, all metal case
  • Low distortion
  • Custom configuration of gain and maximum output

A10160

45MHz 34Vp-p Single Channel Signal Amplifier
A10160 Amplifier

Model A10160 is an ultra-small footprint, wideband, DC coupled amplifier designed for high frequency, high current signal amplification. With a high bandwidth of 45MHz, 34Vp-p into 50Ω and up to 10W output power, the A10160 is the ideal complimentary amplifier to any signal source that needs a supporting power boost for demanding applications.

  • 45MHz bandwidth
  • High amplitude to 34Vp-p into 50Ω
  • High output current drive to 1A
  • Fast transition time of <10ns
  • Small footprint, all metal case
  • Low distortion
  • Custom gain configuration
Disclaimer

The information given here is technical data, not assured product characteristics. It has been carefully checked and is believed to be accurate; however, no responsibility is assumed for inaccuracies. The user has to ensure by adequate tests that the product is suitable for his application regarding safety and technical aspects.
hivolt.de GmbH & Co. KG does not assume any liability arising out of the application or use of any product described.

Safety Advice

Design, installation and inspection of machinery and devices carrying high voltage require accordingly trained and qualified personnel. Appropriate safety rules and directives must be complied with.
Improper handling of high voltage can mean severe injuries or death and may cause serious collateral damage!