GENH series
PROGRAMMABLE HIGH POWER DC-POWER SUPPLIES
The new half-width GENH units provide a wide range of output voltages. Standard models are available with outputs from 0-8V to 0-300V, with efficiencies up to 88%. Like its bigger brothers GENH is packed with features. These include built-in RS232/RS485 interface, constant voltage/constant current operation with automatic crossover, remote sensing, voltage and current adjust via high resolution encoders, high resolution programming with a 16-bit readback and software calibration which removes the need for internal trimmers.
GENH is capable of parallel operation with active power sharing, and through its cooling fan speed control ensures an extended fan life. External voltage programming (0-5V/0-10V), external resistive programming
(0-5K/0-10K) and output voltage and current monitoring (0-5V/0-10V) are all user selectable via the rear panel controls.
Factory fitted options include a GPIB IEEE-488.2 interface (SCPI compliant) for digital programming and Isolated Analogue modules that allow full function master/slave control of a number of supplies operating in series. Accessories include kits that allow two units to be mounted side-by side in a 19-inch rack and several units to be 'stacked' within a rack.
Built-in protective functions include over voltage protection, under voltage limit, foldback protection and over temperature protection.
Safety approvals include UL60950 and EN60950 (TUV).
The units comply with a broad range of EMC regulations including EN55024, EN55022 and FCC.
Features:
- Highest Power Density available: 750W in 1U half-rack
- Wide Range Input 85 - 265Vac Continuous, single phase, 47/63Hz
- Active Power Factor Correction 0.99
- Output up to 600V, Current up to 100A
- Built in RS232/RS485 Interface
- Front Panel Lockout
- Last Setting Memory
| GEN | 6-100 | 8-90 | 12.5-60 | 20-38 | 30-25 | 40-19 | 60-12.5 | 80-9.5 | 100-7.5 | 150-5 | 300-2.5 | 600-1.3 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Uout (VDC) | 6 | 8 | 12.5 | 20 | 30 | 40 | 60 | 80 | 100 | 150 | 300 | 600 |
| Iout (ADC) | 100 | 90 | 60 | 38 | 25 | 19 | 12.5 | 9.5 | 7.5 | 5 | 2.5 | 1.3 |
| Pout (W) | 600 | 720 | 750 | 760 | 750 | 760 | 750 | 760 | 750 | 750 | 750 | 780 |
| SPECIFICATIONS | |
| Input voltage/freq. (*1): | 85 - 265VAC continuous, 47 - 63Hz, single phase |
| Power Factor: | 0.99 @ 100/200VAC, rated output power |
| EN61000-3-2,3 compliance: | Complies with EN61000-3-2 class A and EN61000-3-3 at 20-100% output power |
| Input current 100/200VAC: | 10.5A / 5A |
| Inrush current 100/200VAC: | Less than 25A |
| Parallel Operation: | Up to 4 units in master/slave mode with single wire current balance connection |
| Series Operation: | Up to 2 units. with external diodes. 600V Max to Chassis ground |
| Operating temp.: | 0°C - 50°C, 100% load |
| Storage temp.: | -20°C - 70°C |
| Operating humidity: | 30 - 90% RH (no condensation) |
| Storage humidity: | 10 - 95% RH (no condensation) |
| Vibration: | MIL-810E, method 514.4 , test cond. I-3.3.1 . The EUT is fixed to the vibrating surface. |
| Shock: | Less than 20G , half sine , 11ms, Unit is unpacked |
| Altitude: | Operating: 10000ft (3000m), Derat output current by 2%/100m above 2000m, Non operating: 40000ft (12000m) |
| Cooling: | Forced air flow: from front to rear. No ventilation holes at the top or bottom of the chassis Variable fan speed |
| Dimensions (WxHxD): | 214.0mm x 43.6mm (57.0mm Benchtop version) x 437.5mm (excluding connectors, encoders, handles etc..) |
| Weight: | 4.5kg |
| AC Input connector: | AC Inlet IEC320 |
| Output connectors: | 6V to 60V models: bus-bars (hole D=6.5mm) 80V to 600V models: Meating plug, Phoenix P/N: GIC 2.5/4-ST-7.62 |
*1: For cases where conformance to various safety standards (UL, IEC etc.) is required, to be described as 100-240VAC (50/60Hz).
Options:
- GPIB Interface P/N: IEEE
- Voltage Programming Isolated analog interface P/N: IS510
- Current Programming Isolated analog interface P/N: IS420
Accessories:
Communication cable
RS232/RS485 Cable is used to connect the power supply to the PC Controller
| Mode | RS485 | RS232 | RS232 |
| PC Connector | DB-9F | DB-9F | DB-25F |
| Communication Cable | Shield Ground L=2m | Shield Ground L=2m | FShield Ground L=2m |
| Power Supply Connector | EIA/TIA-568A (RJ-45) | EIA/TIA-568A (RJ-45) | EIA/TIA-568A (RJ-45) |
| P/N | GEN/485-9 | GEN/232-9 | GEN/232-25 |
Serial link cable*
Chaining Power Supply to Power Supply up to 31 units
| Mode | Power Supply Connector | Communication Cable | P/N |
| RS485 | EIA/TIA-568A (RJ-45) | Shield Ground L=50cm | GEN/RJ45 |
* Included with the power supply